P Trap In Basement Floor Drain

P Trap In Basement Floor Drain In Chicago

How to Unclog a Drain — Tips from The Family Handyman

Plumbing Traps – Structure Tech Home Inspections

How to Connect a P-Trap to a Wall or Floor Drain of the Sink

Hole In Basement Floor – Clsa Flooring Guide

Plumbing Traps – Structure Tech Home Inspections

Basement Floor Drain: What They Are and When to Replace Them – Mister Plumber

Clogged Basement Floor Drain Trap • BASEMENT

Bathtub P-Trap In Concrete : Help..basement shower drain leaking? The Home Depot – It

TYWKIWDBI ("Tai-Wiki-Widbee"): If you have a basement

What is A P-Trap? Everything About Drain Traps – Plumbing Sniper

Bathtub P-Trap In Concrete : Help..basement shower drain leaking? The Home Depot – It

## SEO Title: How to Install a P Trap in a Basement Floor Drain

Having a functioning floor drain in the basement is essential for keeping water out of your home. Floor drains are typically located in the lowest point of your basement, and their purpose is to ensure that water can escape from the house without flooding the area. However, it’s important to install a P-trap in order to keep any odors or pests out of the basement. Installing a P-trap is an easy process that can be done with just a few tools and supplies.

### What is a P-Trap?

A P-trap is a U-shaped pipe that is installed below the floor drain. It acts as a barrier to keep odors, sewer gas, and pests from entering the home through the drain. The P-trap also stores some water, creating a seal that prevents any unwanted odors or gases from coming up. It’s important to note that the P-trap should be installed before any other pipes are connected to the drain.

### What You Will Need

In order to install a P-trap in your basement floor drain, you will need the following supplies:

* PVC Drain Pipe

* PVC Fittings

* PVC Primer

* PVC Cement

* Bucket

* Wrench

* Screwdriver

* Plumber’s Tape

* Teflon Tape

### Step 1: Prepare the Area

Before beginning, turn off the main water supply and make sure there is no water flowing through the drain. If there is still water present, use a bucket to scoop it out. Once the area is clear, use a screwdriver to remove any old pipes or fittings that may be present. This will ensure that you have a clean surface to work on.

### Step 2: Measure and Cut Pipe

Once you have removed all of the old pipes and fittings, measure and cut the PVC pipe for your new P-trap. Make sure to leave some extra length so you can make adjustments if needed. Once you have cut your pipe, use plumber’s tape or Teflon tape around the ends of each piece of pipe before connecting them together with fittings. This will ensure that there are no leaks in your system once it is installed.

### Step 3: Assemble Your P-Trap

Now that you have all of your pieces cut and ready to go, begin assembling your P-trap. Start by connecting one end of the pipe to an elbow fitting, then connect this elbow fitting to another short piece of pipe. Next, attach another elbow fitting to this piece of pipe and connect it to another short piece of pipe. Finally, attach one more elbow fitting to this piece of pipe and connect it back to your original piece of pipe. This should form a U-shape with all four pieces of pipe connected together.

### Step 4: Install Your P-Trap

Now that you have your P-trap assembled, it’s time to install it into your basement floor drain. Use PVC primer on all of your pipes and fittings before applying PVC cement. This will ensure that they are properly adhered together once they are installed in the drain. Once everything is secure, turn on the main water supply and check for any leaks in your system.

Installing a P-trap in your basement floor drain can be an easy process with just a few tools and supplies. By following these steps, you can ensure that no unwanted odors or pests enter your home through the drain. Not only will this help keep your basement smelling fresh and clean, but it will also help keep pests such as cockroaches away from your home as well.